The Jasper Electronics CPCI354 is a 350 Watt Power Supply. The module has a .99 power factor corrected AC 90 – 264V, or DC 36-72V or DC 20-28 V. The module is also hot swap, n+1 redundant with internal OR-ing diodes. It features single wire sharing and is available with PICMG Standard 47 pin and optional 38 pin I/O connector configurators.
GENERAL OVERVIEW
Jasper’s Compact PCI Power Supplies comply with the industry standard PICMG requirements and are available in AC or DC input, from 175W to 500W DC output.
Essential details：PCI354-1022-38 M1164 350 Watt cPCI Power Supply
Features:
Hot Swap, N+1 Redundant
.99 Power Factor Corrected AC 90-264V Input
Standard 47 Pin Connector Configuration
The Jasper Electronics CPCI354 is a 350 Watt Power Supply. The module has a .99 power factor corrected AC 90 – 264V, or DC 36-72V or DC 20-28 V. The module is also hot swap, n+1 redundant with internal OR-ing diodes. It features single wire sharing and is available with PICMG Standard 47 pin and optional 38 pin I/O connector configurators.
GENERAL OVERVIEW
Jasper’s Compact PCI Power Supplies comply with the industry standard PICMG requirements and are available in AC or DC input, from 175W to 500W DC output.
FEATURES ON SELECT MODELS INCLUDE:
• AC/DC: 90-264VAC Input – 175, 200, 250, 300, 350, & 500 Watt Models – 3U & 6U x 8HP
• DC/DC: 18-72VDC Input – 175, 200, 250, 300, 350, & 500 Watt Models – 3U & 6U x 8HP
• PICMG 2.11 Compliant
• Active PFC
• UL/CSA, NEMKO/TUV & CE Certified
• RoHS Compliant
• Current Sharing on 3.3, 5 & +12V Rails
• Hot Swap & ORing Diodes N+1 Operation
• Standard 47 Pin Output Connector with 38 & 32 Pin Options (Some Models)
• Models can be ruggedized against high shock, vibration, and humidity to meet MIL-STD-810 requirements
• Customizing To Meet Your System Requirements Is Our Specialty
CPCI-AC-6U-500
lf you need to inquire or purchase ,please send the product models to my email or call medirectly .
sunny He
[Email]sales@xiongbagk.cn
[Mobile]86-18059884797
[WhatsApp] 86-18059884797
[Skype]sales@saulcontrol.com
PCI354-1022-38 M1164 350 Watt cPCI Power Supply
Line/ Load Regulation At the Sense Point, Over Full Input Range 0 – 100% Output Loading
<±1% for V1, V2, V3, sense leads connected. <±5% for V4
Minimum Loading None required for single unit applications. 10% loading required in N+1, N2 configurations
Stability Output drift <±0.2% after 20 minute warm-up
Temperature Coefficient <±0.02%/ºC, 0º – 50ºC, after 20 minute warm-up
Dynamic Response Less than 3% deviation with a 25% load change at 1A/μsec. Output returns to within 1% in less
than 300μsec
Ripple and Noise (PARD) For all outputs, 50mV max or 1% peak-to-peak nominal, which ever is greater, DC to 20MHz
bandwidth with a coaxial probe and 0.1μF/22μF capacitors at the output terminals
Current Sharing/
Parallel N+1 Operation
V1, V2, V3 Outputs. Single wire connection for ±10% current sharing between any number of units
Remote Sense V1, V2, V3 outputs compensate for up to 0.25V total line drop in the load cables. Outputs are
internally sensed if leads are opened
AC Hold-Up Time Outputs remain in regulation >15msec minimum following loss of AC power at low line, full load
Over Current/ Short Circuit Protection Constant current limit on all outputs. Automatic recovery when overload is removed
Over Voltage Protection Non-crowbar type. Any output that exceeds 25% ±10% of nominal Vout will cause all outputs
to latch off. Remote inhibit, enable or power input recycle required to reset.
Over Temperature Protection Internal temperature sensing. Causes all outputs to shut down. Automatic recovery
Under Voltage Warning Any output dropping below 10% of nominal triggers the power fail warning signal
Reverse Sense Protection Outputs latch-off if remote sense connections are installed in reverse. Remote inhibit, enable
or power input recycle required to reset
Over/ Under Shoot None at turn-on or turn-of
1 Year Warranty
