DVC6010 GE31447X012  Digital Valve Controllers on Fisher Type 657 and 667 Actuators

The DVC6010 positioner is one of the DVC6000 series digital valve controllers under the Fisher brand, which is mainly used for direct stroke control valves. Here are some key parameters about DVC6010:
Stem travel: Max 0 to 102mm (4 in), min 9.5mm (3/8 in).
Communication protocols: With the HART communication protocol, information critical to process operation can be easily accessed.
Input signal: 2-wire system 4-20mA circuit power supply.
Current protection: overload current protection and reverse polarity protection.
Output signal range: 0.4bar(6 psi) to 9.5bar(140 psi).
Independent linearity: ±0.5% of the output range.
Add to quote
Categories: ,

Description

Overview

Essential details：DVC6010 GE31447X012  Digital Valve Controllers on Fisher Type 657 and 667 Actuators

Product Description

Refer to figures 1 and 2 for mounting parts identification. Refer to the FIELDVUE DVC5000 Series Digital Valve Controllers Instruction Manual – Form 5335 for DVC5010 digital controller parts identification, and the FIELDVUE DVC6000 Series Digital Valve Controllers Instruction Manual – Form 5647 for DVC6010 digital valve controller part identification. Refer to the appropriate actuator instruction manual for actuator installation, operation, maintenance and parts identification.
1. Isolate the control valve from the process line pressure, release pressure from both sides of the valve body, and drain the process media from both sides of the valve. Shut off all pressure lines to the actuator, releasing all pressure from the actuator.
Use lock-out procedures to be sure that the above measures stay in effect while you work on the equipment.
2. Attach the connector arm (key 108) to the valve stem as follows:
On actuators without side-mounted handwheel, refer to figure 1.
a. Remove one of the stem connector screws. Insert one of the cap screws (key 120) included in the kit through the connector arm (key 108) and start it in the stem connector. Tighten the screw so that the stem connector clamps the valve and actuator stems but still permits the connector arm to be moved.
b. Remove the second stem connector screw. Swing the connector arm into place and start the second screw (key 120) from the kit. Tighten both screws.
On actuators with side-mounted handwheel refer to figure 2. Loosen the lock nut below the travel disc. Insert the connector arm beneath the travel disc and tighten

DVC6010

Product parameter

The DVC6010 positioner is one of the DVC6000 series digital valve controllers under the Fisher brand, which is mainly used for direct stroke control valves. Here are some key parameters about DVC6010:
Stem travel: Max 0 to 102mm (4 in), min 9.5mm (3/8 in).
Communication protocols: With the HART communication protocol, information critical to process operation can be easily accessed.
Input signal: 2-wire system 4-20mA circuit power supply.
Current protection: overload current protection and reverse polarity protection.
Output signal range: 0.4bar(6 psi) to 9.5bar(140 psi).
Independent linearity: ±0.5% of the output range.
In addition, the DVC6010 locator also has some other functions, such as through the HART communicator or personal computer can easily obtain information about the important part of the process control – the control valve itself, as well as a variety of operations, such as obtaining software version level, information string, bit number, description string, date and other general information. Get diagnostic information to help find the cause of the problem, set input and output configuration parameters, and more.
It should be noted that the DVC6010 has been discontinued, and the new replacement model is DVC6200. If you need to use DVC6200 instead of DVC6010, you may need to buy a supporting bracket, but if you used DVC6200 before, you do not need to buy a supporting bracket.

APPLICATION

3. The parts referenced in this step are part of the digital valve controller. Refer to the digital valve controller instruction manual for parts identification. Attach the mounting bracket (key 107) to the digital valve controller housing with screws (key 104).
4. Attach the digital valve controller to the actuator as follows:
On actuators without side-mounted handwheel:
a. Loosely install a hex flange screw (key 105) in the right hole of the lower actuator mounting boss.
b. Position the digital valve controller so the hole in the mounting pad of the mounting bracket goes onto the mounting screw (key 105). Slide the digital valve controller to the left to expose the left hole. Install the left screw (key 105). Tighten both screws (key 105).
On actuators with side-mounted handwheel:
a. Insert a cap screw (key 155) through a washer (key 149) and spacer (key 148). Loosely install the cap screw in the right hole of the lower actuator mounting boss.
b. Position the digital valve controller so the hole in the mounting pad of the mounting bracket goes onto the mounting screw (key 155). Be sure the washer is between the screw head and the mounting bracket.
c. Slide the digital valve controller to the left to align the left hole in the mounting bracket with the left hole in the actuator yoke.
d. Place the second spacer (key 148) between the actuator yoke and the mounting bracket.
Insert the left screw (key 155) with washer (key 149) through the hole in the mounting bracket and spacer. Tighten both screws (key 155).

Shipping

Superiority products DVC6010 GE31447X012  Digital Valve Controllers on Fisher Type 657 and 667 Actuators

147663-01 BENTLY Communication analog output module
125800-01 Bently Nevada Key phase input/output module
140471-01 Bently Nevada Developed I/O module with internal terminal
3500/22M 138607-01 Bently  Detector module
3500/94 145988-01 BENTLY Display module
3500/42M 176449-02 bently nevada Shaft vibration module
3500/92 136180-01 bently nevada  Communication gateway module
136180-01 Bently Nevada Communication gateway module
3500/92-03-01-00 Bently Nevada 3500/92-03-01-00
7264  ABB The four-channel SSI interface module features automatic
MDB-8E  SARTORIUS Load cell
3500/15 127610-01 Bently Nevada  Digital input module
3500/50 133388-02 BENTLY NEVADA  Tachometer monitoring module 4 channels
3500/40-03-00 176449-01 BENTLY NEVADA  Expansion axial position module
3500/15 Plastic panel  BENTLY NEVADA   Ac and DC power supplies
X20CP1586 B&R The core product of B&R’s I/O system line
IC698PSA350 GE  High capacity power module
VMIVME 3215-000 GE  Computer module
201TI GE  Microprocessor-based electrical transmitter
3500/05-01-02-00-00-01 BENTLY  System rack
PM865K02 ABB  controller
3500/22-01-01-00 138607-01 BENTLY  Transient data interface before and after the size card module
IS420UCSBH4A GE Controller module manufactured by General Electric

Related products